![]() ![]() After the mouse and a device are paired, they connect automatically when Bluetooth is enabled and they are within the Bluetooth range. The third-Bluetooth connection light turns solid white for 3 seconds to confirm the connection is established then dims off. The third-Bluetooth connection light (3 ) starts blinking to confirm the pairing mode is enabled.Press the connection-mode button twice on your mouse (within 3 seconds) until the connection-mode light ( 3 ) turns on indicating that the third-Bluetooth connection is selected.NOTE: You can connect a third device to your wireless mouse using Bluetooth. The second-Bluetooth connection light turns solid white for 3 seconds to confirm the connection is established, and then turns off. Confirm that the pairing process on both mouse and device.NOTE: If Mouse MS5320W is not listed, ensure that the pairing mode is enabled on the mouse. From the list of devices, click Dell Mouse. Ensure that the Bluetooth is turned on.ĭ. Click Bluetooth and other devices settings. Pair your mouse with your Bluetooth-enabled computer.ī.The connection-mode light (2 ) blinks for 3 minutes, indicating your mouse is in the pairing mode.Press the connection-mode button twice on your mouse (within 3 seconds) until the connection-mode light (2 ) turns on indicating that the second-Bluetooth connection is selected.You can connect up to two devices with your wireless mouse using Bluetooth. The mouse is paired with your USB device.The connection-mode light (1 ) on the mouse turns on to indicate the Dell Universal pairing, and then turns off.NOTE: The RF device is pre-paired in the factory. Install the Dell Universal USB dongle to the USB port on your computer.NOTE: You can connect a device to your wireless mouse using the Dell Universal pairing. You can pair and switch between a laptop, desktop, and a compatible mobile device. Your Dell wireless mouse can be paired with devices using USB and Bluetooth. NOTE: Ensure that the distance between your computer and mouse is within ten meters. Slide the power switch down to turn on the mouse.Install the AA battery into the battery compartment.Remove the USB dongle from its compartment.Using your fingertip, pry open the cover. Locate the slot on the side of the mouse cover.This would require a lot more work but would turn the humble logitech unifying receiver into a killer software/firmware based KVM.1 Optical sensor 2 Power switch Setting up your wireless mouse I doubt that any of the above would require more than a dozen lines of code to implement (possibly a bit more if you include error chacking etc but the actual implementation shouldn't need much).Īs I'm in now free flow I would suggest that logitech might consider adding DDC/CI ( wikipedia) functionality to Logitech Flow (regardless of whether the above is implemented) which would permit users to switch input on their monitors. This could also require the control key to pressed at the time the keyboard to permit users to switch only the keyboard if they only wanted to switch the keyboard but have the mouse active on the original system (i.e. The only issue I can see is that if the easy switch buttons simply disconnect from one receiver and connect to the other without sending anything to the receiver and therefore the button presses cannot be captured (a bit shortsigheted if that is the case) but this could be worked around by using a key combo (ctrl + numpad 1/2/3)Īn alternative might be to get the receiver to call the "flow" progream whenever a keyboard (re)connects to it. It might even be possible to provide a checkbox/setting to use control key + easy switch button to execute the flow (as per the mouse flow "Switch between settings" option in Logitech Options. Presumably this is done by the "receiver".Ī small change in the Logitech Options UI (add a checkbox) to allow keyboard to "flow", then capture the easy switch button presses to just call the (existing) flow procedure to make the change. From what I can tell Flow works by sending an instruction to the mouse and keyboard to switch to the appropriate "easy switch" setting. I understand that Logitech developers will be busy (find me a developer who isn't) writing code for new products but this has been such a frequently requested feature (since 2017 from what I can tell), I'm surprised/amazed logitech haven't implemented it yet.Īs discussed in other posts this should not be too dificult to implement as the functionality is already there in the form of Flow (albeit windows/mac only). ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |